15 Seconds Flame Burn Time Wire Testing Equipment for Commercial Applications
|
Product Description: The Gas Flow Controls of the Cable Materials Flammability Tester are of high precision, ensuring that the burning gas is supplied at a consistent rate throughout the test. This feature guarantees that the test results are accurate and ......
SKYLINE INSTRUMENTS CO.,LTD
|
UL 790 Flame / Burning Brand Material Test Equipment For Solar Cell Spread UL 1730
|
... of roofs and components. Under this circumsance of A1.82m, B 2.4m and C 3.9m to grade A~C grade for evaluating the sample. At the same time, it can be applied to the test of the flame retardancy of the photovoltaic cell components. Stadards: -ASTM E...
DONGGUAN DAXIAN INSTRUMENT EQUIPMENT CO.,LTD
|
Stainless Steel Wire Testing Equipment For Burning Bunched Cables EN50399
|
... of vertical flame spread, heat release and smoke production of vertically-mounted bunched wires or cables, electrical or optical, under defined conditions. 2. The Cable Heat Release Apparatus and the arrangement and calibration of the instrument to...
DONGGUAN YUYANG INSTRUMENT CO., LTD
|
Stainless Steel Wire Testing Equipment UL910 Standard Level For Combustion Test
|
... of samples were laid on the horizontal airway of the device, and 87.9KW gas Bunsen burner (30, 000BTU/HR) was burned for 20 minutes. Eligibility criteria for the flame shall not extend to 5 feet away from gas Bunsen flame front optical density peak of 0...
Dongguan HOOHA Electrical Equipment Company Limited
|
IEC60695 Electronic Glow Wire Test Equipment/ Plastic Testing Machine
|
...Wire Test Equipment/ Plastic Testing Machine Basic introduction: 1. glow wire test apparatus Accord with IEC60695-2-10, UL 746A, GB/T5169.10, GB4706.1 2. glow wire test apparatus Using electricity heating regulation material (Ni80 / Cr20) of resistanse wire (Φ 4 mm Ni-Cr alloy wire) to 0°C~ 1000°C in 1 min,then with 1.0 N vertically burn it 30s,measure the fire risk by product light-off or holde burning time ,also test...
Dongguan Liyi Environmental Technology Co., Ltd.
|
60 R/Min Wire Testing Equipments
|
...Wire Tester Using Electricity Heating Regulation Material Wire Testing Equipments Product Description: 1. Glow wire tester Accord with IEC60695-2-10, UL 746A, GB/T5169.10, GB4706.1 2. Glow wire tester Using electricity heating regulation material (Ni80 / Cr20) of resistance wire (Φ 4 mm Ni-Cr alloy wire) to 0°C~ 1000°C in 1 min, then with 1.0 N vertically burn it 30s,measure the fire risk by product light-off or hold burning time ,also test...
DONGGUAN YUYANG INSTRUMENT CO.,LTD
|
Needle Flame Flammability Electrical Safety Test Equipment IEC60695-11-5 12 Months Warranty
|
...Flame Flammability Testing Equipment - 12 Months Warranty 1. Introduction The Needle Flame Tester consists of a dia.0.9mm needle burner that tilts to 45 degree from the vertical and is fueled with butane gas. The fire hazard of the specimen is assessed by measuring the burning duration of the specimen, and any ignition of the wrapping tissue and white pine board below the specimen. The equipment specifies a needle-flame test...
Pego Electronics (Yi Chun) Company Limited
|
IEC 60695-2-10 Glow Wire Test Equipment Flame Testing Chamber
|
IEC 60695-2-10 Glow Wire Test Equipment Fire Hazard Testing Chamber Complied Standards & Clauses IEC60695-2-10 "Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure" IEC 60695-2-11 "Fire ......
Sinuo Testing Equipment Co. , Limited
|
Plastic Horizontal Burning Rate Lab Test Equipment ASTM D 635 Flammability GB/T 2408
|
...Burning Rate Testing Equipment ASTM D 635 Flammability GB/T 2408 Descpition The test apparatus is used for the determination combustion performance of plastic and plastic parts,horizontal or vertical burning,under the conditions of 50W flame. Standards: ASTM D 635,UL94 V-0 V-1 V-2,GB/T 2408 Specification: 1.Test......
Dongguan Hust Tony Instruments Co.,Ltd.
|
Flame Temperature Calibration Device 500W / Flame Temperature of Combustion Test Equipment
|
...combustion test equipment. Calibration Procedure Position the copper block 55±1mm above the needle flame burner. Ignite the flame; the time for the copper block temperature to rise from 100°C±2°C to 700°C±3°C must be 54±2 seconds to validate the...
Hai Da Labtester
|
Submit your “flame burn time wire testing equipment” inquiry in a minute :